鍍鋅橋架因其應用范圍廣、成本低，已成為市場上比較常用的電纜橋架。然而，許多人會疑問鍍鋅橋架需不需要做跨接線?答案需要的。下面濟南橋架廠家就來為您講解一番吧。

Galvanized cable tray has become a commonly used cable tray in the market because of its wide range of applications and low cost. However, many people will ask whether the galvanized bridge needs to be jumper? The answer is needed. Next, Jinan Bridge manufacturer will explain it for you.

鍍鋅橋架的材料為“電鍍鋅”，即化學清洗后將鋼板放入電鍍液(含氧化鋅)中。通電后，鋅分子電離并附著在鋼板表面，形成鍍鋅橋。

The material of galvanized bridge is "electro galvanization", that is, put the steel plate into the electroplating solution (including zinc oxide) after chemical cleaning. After being electrified, zinc molecules ionize and adhere to the surface of the steel plate to form a galvanized bridge.

跨接線原理：

Jumper principle:

跨接導線是連接到電氣設備外殼上的線路，用于及時輸出各種原因引起的不電荷或泄漏電流。由于鍍鋅電纜橋架由金屬制成，具有一定的導電性，為了防止電流因泄漏或其他原因在鍍鋅電纜橋架動，通常在電纜橋架上跨接。

Jumper wire is a line connected to the shell of electrical equipment, which is used to output unsafe charge or leakage current caused by various reasons in time. Since the galvanized cable tray is made of metal and has certain conductivity, in order to prevent current from flowing on the galvanized cable tray due to leakage or other reasons, it is usually bridged on the cable tray.

跨接線注意事項：

Jumper precautions:

1.金屬電纜橋架及其支架全長應少與接地(PE)或中性(pen)干線連接2處;

1. The total length of the metal cable tray and its support shall be connected with the grounding (PE) or neutral (pen) trunk line at least 2 places;

2.非鍍鋅電纜橋架之間的連接板兩端應采用銅芯地線連接，地線的小允許截面積不小于4平方毫米;

2. Both ends of the connecting plate between non galvanized cable trays shall be connected by copper core ground wire, and the minimum allowable cross-sectional area of the ground wire shall not be less than 4 mm2;

3.鍍鋅電纜橋架之間連接板的兩端不得與接地線交叉，但連接板的兩端不得少于2個連接固定螺栓，并帶有防松螺母或防松墊圈。

3. The two ends of the connecting plate between galvanized cable trays shall not cross the grounding wire, but the two ends of the connecting plate shall not be less than 2 connecting and fixing bolts, and shall be equipped with locknuts or lock washers.

以上就是關于鍍鋅橋架需不需要做跨接線的回答，答案是肯定的。原因就是為了防止電流泄露或者倒流，總之是為了起見。希望本文章能夠?qū)δ兴鶐椭缒€想了解更多關于橋架的知識，請持續關注我們網站http://m.ymmgjx.net！

The above is the answer to the question of whether the galvanized bridge needs to be jumper, and the answer is yes. The reason is to prevent current leakage or backflow, in short, for safety. I hope this article can help you. If you want to know more about bridge, please continue to pay attention to our website http://m.ymmgjx.net ！