At present, the cable bridge elbows used in power construction are generally well processed by the cable bridge factory before leaving the factory. However, because the construction site conditions are different, some projects need to tailor and process the cable bridge elbows on site, which requires the installation personnel to have certain basic construction knowledge.

施工現場山東電纜橋架大致分為主橋架和分支架。主橋架是由規劃院規劃，依據圖紙施工；分支架是由主橋架引到就地設備的電纜支架，沒有圖紙規劃，依據現場狀況由施工人員來規劃的。常用的彎頭品種包含水平彎頭90°、上下跳彎45°、筆直上下彎頭、水平三通等。下面就以幾個典型常用彎頭制作方法和質量要求來談一下。

The cable bridge in the construction site is roughly divided into main bridge and sub support. The main bridge is planned by the Planning Institute and constructed according to the drawings; The sub support is the cable support led from the main bridge to the local equipment. There is no drawing planning, and it is planned by the construction personnel according to the site conditions. Common elbow varieties include horizontal elbow 90 °、 Jump up and down 45 °、 Straight up and down elbow, horizontal tee, etc. The following is a few typical common elbow manufacturing methods and quality requirements to talk about.
              

克己的山東電纜橋架彎頭、跳彎、三通的銜接處，應先在內側進行點焊固定并把毛刺藥皮打磨潔凈，外側應平坦，縫隙應盡量小且鋸口處平坦規整。電纜橋架彎頭對接無錯邊，焊接后的對口處應打磨平坦、光亮，不該有損害電纜絕緣層的毛刺、銳邊等棱角。

For the joint of Keji cable bridge elbow, jump bend and tee, spot welding should be carried out on the inner side first, and the burr coating should be polished clean. The outer side should be flat, the gap should be as small as possible, and the saw edge should be flat and regular. The butt joint of cable tray elbow shall be free of misalignment. The butt joint after welding shall be polished flat and bright, and there shall be no burr, sharp edge and other edges and corners damaging the cable insulation layer.

在托盤式山東電纜橋架內加鋼筋時，選用添加￠6-8MM圓鋼，內、外側都應補刷油漆。刷油漆前，應把藥皮，焊渣整理潔凈。多層電纜橋架的克己三通及彎頭裝置完成后，折角應在筆直的一致直線上。

When adding reinforcement in tray type cable tray, ￠ 6-8mm round steel shall be added, and the inner and outer sides shall be repainted with paint. Before painting, clean the coating and welding slag. After the completion of Keji tee and elbow device of multi-layer cable tray, the bending angle shall be in a straight and consistent line.