在使用橋架的時候需要注意的問題很多，其中橋架的生產會出現一些問題，所以安裝的時候要多加注意。那我們就來說說知道角度的橋的正確制作方法，僅供參考。
There are many problems that need to be paid attention to when using the bridge, among which there will be some problems in the production of the bridge, so more attention should be paid to the installation. Let's talk about the correct manufacturing method of the bridge with known angle, for reference only.
彎曲后的橋底邊的長度（底邊的斜邊）可以和橋的寬度一樣長，但范圍控制在100-400mm以內。選擇這個長度的兩個點，在橋邊的相對底邊上畫兩條垂直線，選擇橋的彎曲方向作為切割邊；選擇開口邊作為底邊，畫兩條垂直線作為兩個等腰三角形的平分線。確定這個等腰三角形底邊的長度。
The length of the bent bridge bottom edge (the beveled edge of the bottom edge) can be the same as the width of the bridge, but the range is controlled within 100-400mm. Select two points of this length, draw two vertical lines on the opposite bottom edge of the bridge edge, and select the bending direction of the bridge as the cutting edge; Select the open edge as the bottom edge, and draw two vertical lines as the bisector of the two isosceles triangles. Determines the length of the base of this isosceles triangle.
簡單的算法就是以100高的橋架為例。等腰三角形底邊的長度為76.5mm，即100:76.5。用工具切割等腰三角形后，將橋彎曲成由兩個45度彎曲形成的90橋彎頭。
The simple algorithm is to take a 100 high bridge as an example. The length of the bottom edge of isosceles triangle is 76.5mm, i.e. 100:76.5. After cutting the isosceles triangle with a tool, bend the bridge into a 90 bridge elbow formed by two 45 degree bends.
至于改造后限制橋梁長度的彎頭，可以控制任意長度和距離。可以通過簡單的數學計算制作各種角度和長度的彎頭。
As for the elbow that limits the length of the bridge after reconstruction, any length and distance can be controlled. Elbows of various angles and lengths can be made through simple mathematical calculation.
另外，如果生產完成，必然要運輸使用，建議保證電纜橋架的質量。優良的品質可以保證橋梁的承載能力，在運輸和裝載過程中不會變形，可以保證到達施工現場或出廠的條件。
In addition, if the production is completed, it must be transported and used, and the quality of the cable tray must be guaranteed. The excellent quality can ensure the bearing capacity of the bridge, will not deform during transportation and loading, and can ensure the conditions of arriving at the construction site or leaving the factory.
無需確保電纜橋架的安裝。良好的安裝可以大大減少運輸過程中的產品沖突，大大提高產品完整性，并確保電纜橋架到達施工現場時不掉漆。
It is not necessary to ensure the installation of cable tray. Good installation can greatly reduce product conflicts during transportation, greatly improve product integrity, and ensure that the paint does not fall off when the cable tray arrives at the construction site.
適用于電纜橋架包裝。出廠時應妥善處理橋梁碰撞、油漆剝落等問題，并在運輸過程中做好保護和安裝，避免碰撞。
Suitable for cable tray packaging. Bridge collision, paint peeling and other problems shall be properly handled before leaving the factory, and protection and installation shall be done during transportation to avoid collision.
在安裝電纜橋架時，負載是一個非常重要的信息，也是了解數據的重要信息。在安裝過程中，負載非常重要，這也是很多人在選擇負載時會擔心的原因。因為橋架負載會根據不同的情況有不同的選擇。
When installing the cable tray, the load is a very important information, and it is also an important information to understand the data. During the installation process, the load is very important, which is also the reason many people worry about when selecting the load. Because the bridge load will have different choices according to different situations.
濟南橋架還對每一種不同型號和類型的索橋都有固定的承載力。因此，在使用中，在選擇所需的跳線類型和規格時，還建議考慮實際要求和現場要求。
Jinan Bridge also has a fixed bearing capacity for each different model and type of cable bridge. Therefore, in use, actual requirements and site requirements must also be considered when selecting the required jumper type and specification.
The above is the relevant content of Q & A. I hope it can help you. If you have any questions about this issue, you are welcome to follow our website http://m.ymmgjx.net And consult our staff, will serve you wholeheartedly.
濟南火車站
曲阜孔子文化會展中心
山東工藝美院
公安廳服務展示
梯式橋架：工業動力的“呼吸”骨架
