The installation height of the mounting bracket can be adjusted within the range of 2.2-2.8 meters. When selecting 2.2 meters, it is important to prevent human demolition and damage. When selecting 2.8 meters, it is important to pay attention to ventilation pipes and other items that may affect the visual field of the video detector. The horizontal distance between the installation bracket and the parking space line can be adjusted within a range of 3-4 meters. When using dual parking spaces, choose the middle position of the lane (width). This installation bracket should be the lowest installation position for the lifting equipment in the parking lot. When installing brackets in sloping areas, the slope of the installation bracket should be consistent with the building. Install brackets in buildings with circular arcs, and the arcs should be consistent. The installation bracket should be "horizontally and vertically". After the installation of the bracket is completed, use a horizontal ruler to measure whether the bracket meets the horizontal requirements. Use a laser projector to confirm whether the bracket is in a straight line.

設備安裝完成再次確定安裝支架高度與水平距離車位的寬度。 支吊架的選擇? 安裝支架安裝選用的支吊架為一下幾種：雙拉通絲吊架、單拉通絲吊架、角鐵支架。雙拉通絲吊架由通桿螺絲、拉爆、橫梁組成，雙拉通絲吊架每一個吊架選用兩個通桿螺 絲組成。單拉通絲吊架由通桿螺絲、拉爆、吊框組成，單拉通絲吊架每一個吊架選用一個通桿螺 絲組成。角鐵支架，分為U型支架、L型支架。其主要材質為角鐵，作用為固定安裝支架，確保橋 架不會隨意晃動?單拉通絲吊架如下圖使用卷尺，確認地面點位。根據視頻車位引導系統視頻探測器的安裝要求，即視頻探測器距離車位線前方位置3米，當車位為相對應的車位時候，安裝支架應當選擇在車輛行駛道路的中間位置。

Once the equipment installation is completed, determine the height of the installation bracket and the width of the horizontal distance from the parking space again. The selection of supports and hangers? The following types of supports and hangers are selected for the installation of brackets: double pull through wire hangers, single pull through wire hangers, and angle iron brackets. The double pull through wire hanger is composed of through rod screws, pull-out bolts, and crossbeams. Each hanger of the double pull through wire hanger is composed of two through rod screws. The single pull through wire hanger is composed of a through rod screw, a pull-out bolt, and a hanging frame. Each hanger of the single pull through wire hanger is composed of a through rod screw. Angle iron brackets are divided into U-shaped brackets and L-shaped brackets. Its main material is angle iron, which serves as a fixed installation bracket to ensure that the bridge does not shake at will? Use a tape measure to confirm the ground position of the single pull through wire hanger as shown in the figure below. According to the installation requirements of the video detector in the video parking guidance system, the video detector should be located 3 meters in front of the parking line. When the parking space is the corresponding parking space, the installation bracket should be selected in the middle of the vehicle's driving road.

1.使用“激光投線儀”確認頂棚通桿螺絲的位置，并使用電鉆進行開孔。上圖激光投線儀，確認安裝支架支吊架位置。

1. Use the "laser line projector" to confirm the position of the ceiling through rod screws and use an electric drill for drilling. Confirm the position of the installation bracket support and hanger for the laser line projector shown above.

2.安裝支架支吊架間距為3米，在直線與彎通連接處0.3米的位置使用吊架。安裝支架的安裝高度為2.5米。

2. Install brackets with a spacing of 3 meters between supports and hangers, and use hangers at a position of 0.3 meters at the connection between straight lines and bends. The installation height of the bracket is 2.5 meters.

3.根據現場地面與頂棚的高度計算通桿螺絲的長度，并使用切割機進行切割處理。注：確認通桿螺絲位置時建議比原來長度稍長幾公分確保可以小幅度調整安裝支架水平位置。 五、使用拉爆與通桿螺絲相結合將通桿螺絲固定在頂棚確定的位置，并在通桿螺絲的下端安裝吊框，吊框選用安裝支架廠商提供的原件。

3. Calculate the length of the through rod screw based on the height of the ground and ceiling on site, and use a cutting machine for cutting treatment. Note: When confirming the position of the through rod screw, it is recommended to slightly extend the original length by a few centimeters to ensure that the horizontal position of the installation bracket can be adjusted slightly. 5、 Use a combination of pull-out and through-pole screws to fix the through-pole screws at the designated position on the ceiling, and install a hanging frame at the lower end of the through-pole screws. The hanging frame is selected from the original components provided by the installation bracket manufacturer.

4.安裝支架組裝與安裝安裝支架的直線段之間連接使用廠商提供的連接件。安裝支架應當在建筑物伸縮出設置安裝支架伸縮 縫。具體辦法：安裝支架連接處一端安裝支架連接片上螺絲不上即可安裝支架直線段安裝時，直接將安裝支架穿過吊框，連接縫使用聯接片連接。

4. The connection between the assembly of the installation bracket and the straight section of the installation bracket shall be made using the connection pieces provided by the manufacturer. The installation bracket should be equipped with expansion joints at the expansion point of the building. Specific method: Install the bracket at one end of the bracket connection point. If the screw on the bracket connection piece is not tightened, the bracket can be installed. When installing the straight section of the bracket, directly pass the installation bracket through the hanging frame, and use the connection piece to connect the connection seam.

5.并安裝跨界軟銅線：安裝支架位置矯正與檢查確保安裝支架安裝完成之后處于水平位置，如不符合要求應當立即進行調整。確保安裝支架前端與后端處于同一直線上，如不符合要求立即進行調整。

5. Install crossover flexible copper wire: Correct and inspect the position of the installation bracket to ensure that it is in a horizontal position after installation. If it does not meet the requirements, it should be adjusted immediately. Ensure that the front and rear of the installation bracket are in the same straight line, and adjust immediately if they do not meet the requirements.

6.確保安裝支架連接處應有軟通線連接，如沒有應當立即增加。確保安裝支架某一直線段起始端與末端應當有角鐵加進行固定，安裝支架超過一定距離時應當選用角鐵支架進行固定。確保安裝支架距離地面高度一致，如不符合要求立即進行調整。確保安裝支架距離車位線位置符合設計要求，如不符合要求立即進行調整。

6. Ensure that there should be a flexible cable connection at the connection point of the installation bracket. If not, it should be added immediately. Ensure that the starting and ending ends of a certain line segment of the installation bracket should be fixed with angle iron brackets. When the installation bracket exceeds a certain distance, angle iron brackets should be selected for fixation. Ensure that the installation bracket is at the same height from the ground, and adjust it immediately if it does not meet the requirements. Ensure that the distance between the installation bracket and the parking line meets the design requirements. If it does not meet the requirements, adjust it immediately.

本文由山東電纜橋架友情奉獻.更多有關的知識請點擊:http://m.ymmgjx.net真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Shandong Cable Bridge Friendship. For more relevant knowledge, please click on: http://m.ymmgjx.net Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned