1. When it is necessary to shield the cable network from electrical interference or when there is a requirement to protect against external influences (such as corrosive liquids, flammable dust, etc.), (FB) type slot type composite anti-corrosion shielding cable tray (with cover) should be selected.

2、強腐蝕性環境應采用(F)類復合環氧樹脂防腐阻燃型電纜橋架。托臂、支架也要選用同樣材料，提高橋架及附件的使用壽命，電纜橋架。在容易積灰和其它需遮蓋的環境或戶外場所宜加蓋板。

2. Strong corrosive environments should use (F) composite epoxy resin anti-corrosion and flame-retardant cable trays. Brackets and brackets should also be made of the same materials to improve the service life of cable trays and accessories. Cover plates should be added in environments or outdoor areas that are prone to dust accumulation and require covering.

3、除上述情況外，可根據現場環境及技術要求選用托盤式、槽式、梯級式、玻璃防腐阻燃電纜橋架或鋼質普通型橋架。在容易積灰和其它需遮蓋的環境或戶外場所宜加蓋板。

3. In addition to the above situations, tray type, trough type, stepped type, glass anti-corrosion flame-retardant cable tray or steel ordinary type tray can be selected according to the on-site environment and technical requirements. Cover plates should be added in environments or outdoor areas that are prone to dust accumulation and require covering.

4、在公共通道或戶外跨越道路段，底層梯級的底部宜加墊板或在該段使用托盤。大跨距跨越公共通道時，可根據用戶要求提高橋架的載荷能力或選用行架。

4. In public passages or outdoor crossing road sections, it is advisable to add a pad at the bottom of the bottom step or use a pallet at that section. When crossing a public passage with a large span, the load capacity of the bridge can be increased or a gantry can be selected according to user requirements.

5、大跨距(>3m)要選用復合型橋架(FB)。

5. Composite cable trays (FB) should be used for large spans (>3m).

6、戶外要選用復合環氧樹指橋架(F)。

6. Composite epoxy tree finger bridge (F) should be selected for outdoor use.

電纜橋架的小知識 ，您了解多少？

How much do you know about cable trays?

電纜橋架廠家直銷規格選擇

Selection of direct sales specifications for cable tray manufacturers

1、復合環氧樹脂電纜橋架的寬度和高度就按下表選擇，并應符合電纜真充率不超過有關標準規范的規定值，動力電纜可取40-50，控制電纜可取50-70，另外需予留10-25的式程發展余量。

1. The width and height of the composite epoxy resin cable tray should be selected according to the following table, and should comply with the cable true filling rate not exceeding the specified values of relevant standards and specifications. Power cables can be taken as 40-50, control cables can be taken as 50-70, and a process development margin of 10-25 should be left.

2、各種彎通及附件規格應符合工程布置條件并與橋架相配套。

2. The specifications of various bends and accessories should comply with the engineering layout conditions and be matched with the bridge.

3、支、吊架規格的選擇，應按橋架規格、層數、跨距等條件配置。并應滿足荷載的要求。

3. The selection of support and hanger specifications should be based on conditions such as cable tray specifications, number of layers, and span. And it should meet the requirements of the load.

對于電纜橋架的支、吊架的配置

Configuration of supports and hangers for cable trays

1、戶內支、吊短跨距一般采取1.5-3m;戶外立柱中跨距一般采取6m。

1. The short span of indoor support and suspension is generally 1.5-3m; The span of outdoor columns is generally 6 meters.

2、非直線段的支、吊架配置就遵循以下原則：當橋架寬度<300mm時，應在距非直線段與直線結合處300-600m的直線段側設置一個支、吊架;當橋架寬度>300mm時，除符合下述條件外，在非直線段中部還應增設一個支、吊架。

2. The configuration of supports and hangers for non linear sections follows the following principles: when the bridge width is less than 300mm, a support or hanger should be set on the side of the straight section 300-600m away from the junction of the non linear section and the straight line; When the width of the bridge is greater than 300mm, in addition to meeting the following conditions, a support and hanger should also be added in the middle of the non linear section.

3、拉擠玻璃鋼電纜橋架多層設置時層間中間距為200，250，300，350mm。

3. When the pultruded fiberglass cable tray is set in multiple layers, the interlayer spacing is 200250300350mm.

4、橋架直線段每隔50m應予留伸縮縫20-30mm(金屬橋架)。

4. Expansion joints of 20-30mm (metal bridge) should be left every 50m in the straight section of the bridge.

本文由山東電纜橋架網友情奉獻.更多有關的知識請點擊:http://m.ymmgjx.net真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Shandong Cable Tray Network. For more information, please click on: http://m.ymmgjx.net Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned