電纜橋架鍍鋅及外觀要求

　　Galvanization and appearance requirements for cable trays

　　要求：

　　requirement:

　?、贌峤冧\橋架鍍層表面應均勻，無毛刺、過燒、掛灰、傷痕、局部未鍍鋅。每節橋架上直徑小于2mm的漏鍍點， 每米不超過2個，且在任一1m?面積內不得有兩個及2個以上漏鍍點。不得有影響安裝的鋅瘤。

　　① The surface of the hot-dip galvanized bridge coating should be uniform, free of burrs, overburning, dust hanging, scars, and partial lack of galvanizing. There shall be no more than 2 plating leakage points on each bridge with a diameter less than 2mm per meter, and there shall be no two or more plating leakage points within any 1m ? area. There must be no zinc nodules that affect installation.

　　②電鍍鋅的鋅層表面應光滑均勻，致密。不得有起皮、氣 泡、花斑、局部未鍍、劃傷等缺陷。

　　② The surface of the zinc layer of electroplated zinc should be smooth, uniform, and dense. There shall be no defects such as peeling, bubbles, flower spots, partial uncoated areas, scratches, etc.

　　③噴塑層的表面應平整、光滑、均勻、不起皮、無起皺、 氣泡等缺陷。

　?、?The surface of the spray coating should be flat, smooth, uniform, without peeling, wrinkling, bubbles or other defects.

　　④螺紋的鍍層應光滑，螺栓連接件應能擰入。

　　④ The coating of the thread should be smooth, and the bolt connection should be able to be screwed in.

　?、輼蚣芎缚p表面均勻，不得有漏焊、裂紋、夾渣、燒穿、 弧坑等缺陷。

　?、?The surface of the bridge welding seam should be uniform and free of defects such as missed welding, cracks, slag inclusion, burn through, arc craters, etc.

　?、迾蚣芡庑统叽鐟蠄D紙及工藝要求，表面應無變形、 劃傷、開裂現象。

　?、?The external dimensions of the bridge should comply with the drawings and process requirements, and the surface should be free of deformation, scratches, and cracking.

　?、邩蚣軆蓪厬叫校瑑蓚冗厡Φ走厬怪?，斷面形狀端 正，無彎曲、裂紋、邊緣毛刺等缺陷。

　?、?The two sides of the bridge should be parallel, and the two sides should be perpendicular to the bottom edge. The cross-sectional shape should be straight and free of defects such as bending, cracks, and edge burrs.

　　⑧橋架內側應平整光滑，無損傷電纜絕緣的凸起尖角。

　?、?The inner side of the cable tray should be flat and smooth, without any protrusions or sharp corners that damage the cable insulation.

　　⑨橋架端頭毛刺高度不應大于0.1mm。⑩橋架直線段每米偏差應不大于1mm，垂直度（底邊對側 邊）允許偏差1/200。

　　⑨ The height of burrs at the end of the bridge should not exceed 0.1mm. The deviation per meter of the straight section of the bridge should not exceed 1mm, and the allowable deviation for verticality (bottom edge to side edge) is 1/200.

　　本文由  濟南橋架 友情奉獻.更多有關的知識請點擊  http://m.ymmgjx.net/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Bridge For more related knowledge, please click http://m.ymmgjx.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.

　　電纜橋架鍍鋅及外觀要求

　　Galvanization and appearance requirements for cable trays

　　要求：

　　requirement:

　?、贌峤冧\橋架鍍層表面應均勻，無毛刺、過燒、掛灰、傷痕、局部未鍍鋅。每節橋架上直徑小于2mm的漏鍍點， 每米不超過2個，且在任一1m?面積內不得有兩個及2個以上漏鍍點。不得有影響安裝的鋅瘤。

　?、?The surface of the hot-dip galvanized bridge coating should be uniform, free of burrs, overburning, dust hanging, scars, and partial lack of galvanizing. There shall be no more than 2 plating leakage points on each bridge with a diameter less than 2mm per meter, and there shall be no two or more plating leakage points within any 1m ? area. There must be no zinc nodules that affect installation.

　?、陔婂冧\的鋅層表面應光滑均勻，致密。不得有起皮、氣 泡、花斑、局部未鍍、劃傷等缺陷。

　?、?The surface of the zinc layer of electroplated zinc should be smooth, uniform, and dense. There shall be no defects such as peeling, bubbles, flower spots, partial uncoated areas, scratches, etc.

　?、蹏娝軐拥谋砻鎽秸?、光滑、均勻、不起皮、無起皺、 氣泡等缺陷。

　?、?The surface of the spray coating should be flat, smooth, uniform, without peeling, wrinkling, bubbles or other defects.

　　④螺紋的鍍層應光滑，螺栓連接件應能擰入。

　?、?The coating of the thread should be smooth, and the bolt connection should be able to be screwed in.

　?、輼蚣芎缚p表面均勻，不得有漏焊、裂紋、夾渣、燒穿、 弧坑等缺陷。

　　⑤ The surface of the bridge welding seam should be uniform and free of defects such as missed welding, cracks, slag inclusion, burn through, arc craters, etc.

　?、迾蚣芡庑统叽鐟蠄D紙及工藝要求，表面應無變形、 劃傷、開裂現象。

　　⑥ The external dimensions of the bridge should comply with the drawings and process requirements, and the surface should be free of deformation, scratches, and cracking.

　?、邩蚣軆蓪厬叫?，兩側邊對底邊應垂直，斷面形狀端 正，無彎曲、裂紋、邊緣毛刺等缺陷。

　　⑦ The two sides of the bridge should be parallel, and the two sides should be perpendicular to the bottom edge. The cross-sectional shape should be straight and free of defects such as bending, cracks, and edge burrs.

　　⑧橋架內側應平整光滑，無損傷電纜絕緣的凸起尖角。

　　⑧ The inner side of the cable tray should be flat and smooth, without any protrusions or sharp corners that damage the cable insulation.

　　⑨橋架端頭毛刺高度不應大于0.1mm。⑩橋架直線段每米偏差應不大于1mm，垂直度（底邊對側 邊）允許偏差1/200。

　　⑨ The height of burrs at the end of the bridge should not exceed 0.1mm. The deviation per meter of the straight section of the bridge should not exceed 1mm, and the allowable deviation for verticality (bottom edge to side edge) is 1/200.

　　本文由  濟南橋架 友情奉獻.更多有關的知識請點擊  http://m.ymmgjx.net/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Bridge For more related knowledge, please click http://m.ymmgjx.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.