電纜橋架各種彎頭配件一般都是在廠家預訂好的，在現場做的缺點一是不美觀，二是不耐用（非常是噴涂及熱浸鋅處理的），三是費工時，非常是有的項目監理是不允許在現場加工的，所以通常是用戶提前按施工圖紙出好清單，由廠家訂制好后再直接進行安裝。
Cable tray elbow accessories are generally ordered in the factory, in the field to do the disadvantages of one is not beautiful, two is not durable (especially spraying and hot dip zinc treatment) , three is time-consuming, in particular, some project management is not allowed on-site processing, so usually users in advance according to the construction drawings out a good list, by the factory after the direct installation.
因為它在安裝過程中，用到的彎頭一般有三種：一種是水平彎，一是垂直上下彎，還有一種是“之”字彎。山東電纜橋架蘇鑫告訴你制作方電纜橋架其實就是解方程，學不好數學的制作不出來。
Because it is installed in the process, there are generally three kinds of elbow: a Horizontal Bend, a vertical up and down bend, and a “Zigzag”bend. Shandong Cable Bridge Su Xin told you to make the square cable bridge is actually the solution of the equation, not good math to make out.
例子：400X150橋架作45°“之”字彎
EXAMPLE: 400X150 bridge with 45 ° Zigzag
取15 cmX0.8從橋架側面，在橋架下畫一點，將這段距離相等，然后將三個點連接成45°等腰三角形(另一方)，然后切掉這個三角，形成45°彎，然后用所要做的高度 X1.41為里邊的頂點再畫三角形，然后再用所要做的高度 X1.41為里邊的那個頂點再畫三角形。90°角是畫要做的三角形的2倍，比如400X150作水平彎頭，那么把400X2畫的三角形切成三角形就可以了，如果要做豎直的彎頭，取150X2。
Take 15 cm x 0.8 from the side of the bridge, draw a point under the bridge, equalize the distance, then connect the three points to form a 45 ° Isosceles Triangle (the other side) , then cut the triangle to form a 45 ° curve, then use the height you want to do X1.41 to draw another triangle for the innermost Vertex, and then use the height you want to do X1.41 to draw another triangle for the innermost vertex. If the angle of 90 ° is twice that of the triangle to be drawn, such as 400X150 for the horizontal elbow, then cut the 400X2 triangle into a triangle. If you want to make a vertical elbow, take 150X2.
山東電纜橋架蘇鑫概括公式：例如45度斜度的彎頭，你只要記住這句話就知道了“爬坡45度，橋高乘以0.8中分三條線為一個彎，斜邊是爬坡高度乘以1.41度，斜邊是爬坡高度乘以0.8，而斜坡高度乘以1.41，斜邊是爬坡高度乘以0.8，而斜坡高度乘以0.8，斜坡高度乘以0.8，斜坡高度乘以1.41。
Su Xin General Formula of Shandong Cable Bridge Frame: For example, Bend with 45 degree slope, you just have to remember the phrase, “Climb 45 degrees, Bridge Height Times 0.8 mid-line is a curve, ramp height times 1.41 degrees, ramp height times 0.8, ramp height times 1.41, ramp height times 1.41, ramp height times 0.8, ramp height times 0.8, ramp height times 0.8, ramp height times 1.41.
α值同“一”中角α值；本圖的b值與 “一”中的b值不同，為層間距值。
The value of α is the same as the value of angle α in “One”, and the value of B in this figure is different from the value of B in “One”, which is the value of interval.
制作層彎頭：
層兩個彎頭的做法同“一”中彎頭的做法，兩個彎頭間距a值由現場確定，但需滿足電纜彎曲半徑的要求。
制作第二層彎頭：
計算第二層橋架個彎頭的定位尺寸e：
首先量出層橋架定位尺寸d值，則e=d+btg1/2α
式中：b為層間距，角α值同“一”中角α值
依照“一”的方法制作第二層彎頭的第1個切口α；
計算兩個彎頭間距c值：c=2btg1/2α+a 式中：b為層間距，a為層橋架兩個彎頭的間距
依照“一”的方法制作第二層彎頭的第2個切口α；
計算補償尺寸h：h=2 btg1/2α
制作第三層彎頭：制作方法同第二層彎頭 f=e+btg1/2α g=2btg1/2α+c
Making elbow of the first layer: The method of the two elbows of the first layer is the same as that of the elbows in "1". The distance a between the two elbows is determined on site, but the bend radius of the cable must be met. Make the second layer elbow: calculate the positioning size e of the first elbow of the second layer bridge: first measure the positioning size D value of the first layer bridge, then E = D BTG1/2 α : B is the layer spacing, and the Angle α value is the same as "one" in accordance with the method of "one" to make the first notch α of the second layer elbow; Calculate the spacing c value of two elbows: c=2btg1/2α In formula A: B is the spacing between layers, a is the spacing between two elbows of the bridge of the first layer. The second notch α of the second layer elbow is made according to the method of "one". Calculate the compensation size H: h=2 bTG1/2 α Fabricate the third layer elbow: fabricate the same method as the second layer elbow F = E bTG1/2 α g= 2BTG1/2 α C
數學不好的真計算不出來，在這里就能看出來，制作一個彎頭都需要這么多的解方程，更何況是制作整個橋架，可以想象一下
山東電纜橋架蘇鑫團隊都是怎樣的一批人士了。
You can’t really do it if the math is bad, but you can see here that it takes so many equations to make a bend, not to mention the whole bridge, can Imagine Shandong Cable Bridge Su Xin team is what kind of a group of people.
濟南火車站
曲阜孔子文化會展中心
山東工藝美院
公安廳服務展示
梯式橋架：工業動力的“呼吸”骨架
